image
PSoC 62S2 Wi-Fi BT Kit

Infineon PSoC™ 62S2 Wi-Fi® BT® Pioneer Kit Overview

 

The PSoC 62S2 Wi-Fi BT Pioneer Kit enables you to evaluate and develop your applications using the PSoC 62 Series MCU (hereafter called “PSoC 6 MCU”) and CYW43012 WICED Wi-Fi/BT combo device. PSoC 6 MCU is Cypress’ latest, ultra-low-power PSoC specifically designed for wearables and IoT products. 

PSoC 6 MCU is a true programmable embedded system-on-chip, integrating a 150-MHz Arm® Cortex®-M4 as the primary application processor, a 100-MHz Arm Cortex-M0+ that supports low-power operations, up to 2 MB Flash and 1 MB SRAM, Secure Digital Host Controller (SDHC) supporting SD/SDIO/eMMC interfaces, CapSense® touch-sensing, and programmable analog and digital peripherals that allow higher flexibility, in-field tuning of the design, and faster time-to-market. 

The PSoC 6 BLE Pioneer Board offers compatibility with Arduino™ shields. 

The board features a PSoC 6 MCU and a CYW43012 Wi-Fi/Bluetooth combo module. Cypress CYW43012 is a 28-nm, ultra-low-power device that supports single-stream, dual-band IEEE 802.11n-compliant Wi-Fi MAC/ baseband/radio, and Bluetooth 5.0 BR/EDR/LE. The WLAN section supports an SDIO interface to the host MCU (PSoC 6 MCU), and the Bluetooth section supports a high-speed 4-wire UART interface to the host MCU. In addition, the board features an onboard programmer/debugger (KitProg3), a 512-Mbit Quad SPI NOR flash, a 4-Mbit Quad SPI F-RAM, a micro-B connector for USB device interface, a 5-segment CapSense slider, two CapSense buttons, a microSD card holder, an RGB LED, two user LEDs, one potentiometer, and two push buttons. The board supports operating voltages from 1.8 V to 3.3 V for PSoC 6 MCU

 

PSoC 62S2 Wi-Fi BT Pioneer Kit

 

Features

  • CY8CMOD-062S2-43012 carrier module that contains
  • PSoC 6 MCU (CY8C624ABZI-S2D44)
  • Murata 1LV ultra-small 2.4GHz/5.0GHz WLAN and BLUETOOTH functionality module based on CYW43012
  • 512-Mbit external Quad SPI NOR Flash that provides a fast, expandable memory for data and code
  • 4-Mbit quad SPI ferroelectric random-access memory (F-RAM)
  • KitProg3 onboard SWD programmer/debugger with USB-UART and USB-I2C bridge functionality
  • CAPSENSE™ touch-sensing slider (5 elements), two buttons, based on self-capacitance (CSD) and mutual-capacitance (CSX) sensing.
  • A micro-B connector for the USB device interface for PSoC 6 MCU
  • 1.8V and 3.3V operation of PSoC 6 MCU is supported
  • Two user LEDs, an RGB LED, two user buttons, and a reset button for PSoC 6 MCU
  • A potentiometer
  • One mode-selection button and one status LED for KitProg3
  • A MicroSD Cardholder

 

Kit Content

  • PSoC 62S2 Wi-Fi BT pioneer board
  • USB Type-A to Micro-B cable
  • Four jumper wires (4" each)
  • Two jumper wires (5" each)
  • Quick-start guide

 

Ad